Hi guys, Welcome to the Advanced Video Search Engine, and you are watching Viewrail Stand Off Pins Installation Animation. That video is uploaded by Viewrail at 2020-09-08T12:16:59-07:00. We are promoting this video only for entertainment and educational purpose only. So, I hope you like & enjoy it. [6M4PUAxgjZc]
| Name | Viewrail Stand Off Pins Installation Animation |
| Video Uploader | Video From Viewrail |
| Upload Date | This Video Uploaded At 08-09-2020 19:16:59 |
| Video Discription | Do you have questions about the installation process of Viewrails Stand Off Pins? Are you thinking about utilizing them on your next DIY project? Look no further! THis rendering provides you with a high quality, step-by-step look at the installation of a Viewrail Stand Off Pin. (0:00) INTRO Before you begin, mark the locations where your lag bolts will fasten to secure your Standoff Pins. Keep the overall system in mind as each of the 4 Standoff Pins will need to be mounted before you can install your glass panel. (0:14) STEP 1: Installing Your Standoff Pin Base On your marked location, use a ¼” drill bit and predrill a 4.5” holes for your lags. Set the Pin Base in place and run the provided ⅜” lag bolt into the supporting structure. Once in place, take the Glass Adjuster Nut, remove the protective cover, and adhere its bushing to the outward facing surface. Slide the Glass Adjuster Nut into the Glass Pin Base. (1:12) STEP 2: Installing Your Standoff Pin Cover Next, using the provided allen wrench, fasten the Glass Pin Adjuster Screw into Glass Adjuster Nut until snug. Then take the Glass Pin Cover, remove the protective lining, and attach its bushing to the outside facing surface. Use the Center Bushing to sit around the extrusion. Tighten the Glass Pin Cover onto the Adjuster Nut. (1:52) STEP 3: Installing Your Glass Panel Once all 4 Standoff Pins are in place, you are ready for glass installation. It may be necessary at this point to grab a partner for assistance in transporting the glass and holding it in place. Use the provided suction cups to hold the glass panel in front of the Standoff Pins. (2:14) STEP 4: Adjusting Your Pins Location Using the provided allen wrench, you can also loosen the Adjuster Nut to slide the Pin Cover horizontally or vertically to make sure it lines up with the holes in the glass. Depending on the degree of tightening, these can be adjusted to make sure the glass is plumb. Once your glass is set, simply retighten. (2:40)STEP 5: Locking Your Glass Panel in Place Next, insert the Set Screw into the Pin Cover and tighten. This will lock the assembly in place. If not plumb, loosen the set screw and use the Glass Pin Tool and Spanner Wrench to adjust. Retighten the set screw afterwards to lock in place. (3:21) STEP 6: Installing Your Glass Pin Cap Finally, take the Glass Pin Cap, remove the protective cover, and adhere its bushing to the side facing the glass. Tighten the cap in place. You can use the Spanner Wrench to lock into the cap for a tight grip. Repeat these steps for each of your Standoff Pins. Looking for inspiration for your next project? Check out our Completed Project Gallery here: https://www.viewrail.com/completed-projects/ Be sure to keep up with us on all our social media channels! Facebook: https://www.facebook.com/viewrail/ Instagram: https://www.instagram.com/viewrail/ Pinterest: https://www.pinterest.com/viewrail/glass-railing/ 6M4PUAxgjZc |
| Category | Howto & Style |
| Tags | Viewrail | Viewrail stairs | Floating stairs | Elegant stairs | modern stairs | modern railing | elegant modern stairs | modern infill | stainless steel | cable railing | modern cable railing | Glass railing | glass stairs | DIY | Glass breaking | skunkworx | research and development | Viewrail glass break |
